The SpiderR40ESP32C3 turns a radino40 radio module into a working device: USB-C, antenna connector, power supply and every pin of the module on solder pads — on 50.8 × 25.4 mm. An ESP32-C3 with WiFi and Bluetooth sits on the board as well, sharing a UART with the radino40.
The board ships with the radino40 already soldered on. Which module sits on it determines the radio technology — the board itself stays the same.
- Carrier for radino40 modules: CC1101, DW1000, DW3000
- ESP32-C3FH4 with 4 MB flash, WiFi and Bluetooth LE
- USB-C for power, programming and the serial connection
- RP-SMA antenna socket for the radino40
- Every pin of the radino40 on solder pads, 2.54 mm pitch
- Five free pins of the ESP32-C3 (IO0 to IO4)
- Powered from USB-C, 5 V or 24 V — the inputs are decoupled
- 3.3 V from a linear regulator, up to 600 mA
- Two buttons, three LEDs
- 50.8 × 25.4 mm, 12 g
The ESP32-C3
The ESP32-C3 is delivered without firmware; only the radino40 is programmed. With firmware of your own, the ESP32-C3 can handle the network connection, for instance, while the radino40 runs the radio traffic. It has its own USB connection on the USB-C socket – see below.
The price shown is that of the board. Choose the radino40 above – it is soldered on and the board is tested before delivery; its price is added.
USB-C: The plug orientation selects the chip
The USB-C socket carries two data pairs: one goes to the radino40, the other to the ESP32-C3. A USB cable connects only one of them to the computer – which chip appears depends on the plug orientation. If the chip you want does not appear, flip the plug. Power works in both orientations.
The radino40 appears as USB device 1DA9:0042 (in the bootloader 1915:521F), the ESP32-C3 as 303A:1001. An ESP32-C3 without firmware normally connects and disconnects over and over; with Boot and Reset pressed together it stays visible. Label the cable afterwards, for example “ESP”.
Assembly options
| Part no. | radino40 | What for | Price |
| 901.637B | CC1101 433 MHz | narrowband, long range | 30.00 € |
| 901.637B002 | CC1101 868 MHz | narrowband, SRD band | 30.00 € |
| 901.637B001 | DW1000 | ultra-wideband, positioning | 39.00 € |
| 901.637B004 | DW1000 with TCXO | ultra-wideband, tighter frequency tolerance | 47.00 € |
| 901.637B003 | DW3000 | ultra-wideband to FiRa | 50.00 € |
The picture shows option 901.637B with the radino40 CC1101 433 MHz. The other options differ only in the module soldered on.
Links & Downloads:
| Weight | 12 g |
|---|---|
| Dimensions | 51 × 25 × 3,5 mm |
| Funkmodul | radino40 DW1000, radino40 DW1000 TCXO, radino40 DW3000, radino40 CC1101 433 MHz, radino40 CC1101 868 MHz |
| HS Code | 85423190 |
| Material | Leiterplatte, ohne Gehäuse |
| Colour | Blau |
| Spannungsversorgung | USB-C |
SpiderR40ESP32C3 – development board for radino40
The SpiderR40ESP32C3 turns a radino40 radio module into a working device: USB-C, antenna connector, power supply and every pin of the module on solder pads — on 50.8 × 25.4 mm. An ESP32-C3 with WiFi and Bluetooth sits on the board as well, sharing a UART with the radino40.
excl. VAT plus shipping
Lieferzeit: ships immediately
Planning a larger quantity? Tell us how many and we will send you a quote.





